Bilatu
90-tik 61-80 emaitza erakusten
Enhancing surface integrity of A7050-T7451 aluminium alloy by pneumatic machine hammer peening
(Elsevier Ltd., 2022)
Aerostructures withstand cyclic mechanical loads and therefore, their design must fulfil surface integrity and fatigue strength requirements. This paper studies the effect of pneumatic machine hammer peening on surface ...
Influence of cryogenic grinding surface on fatigue performance of carburised 27MnCr5
(Elsevier, 2023)
Automotive transmission components are subjected to cyclic loads and, thus, must have a reliable fatigue performance. Since fatigue cracks nucleate at the surface, it is necessary to guarantee that its surface integrity ...
Sensitivity analysis of the input parameters of a physical based ductile failure model of Ti-6Al-4V for the prediction of surface integrity
(Elsevier Ltd, 2020)
In machining of Ti-6Al-4V, it is commonly reported the appearance of segmented chip produced by adiabatic shearing (at high cutting speeds) and lack of ductility (at low cutting speeds). Moreover, machining is a manufacturing ...
Identification of the Parameter Values of the Constitutive and Friction Models in Machining Using EGO Algorithm: Application to Ti6Al4V
(MDPI, 2022)
The application of artificial intelligence and increasing high-speed computational performance is still not fully explored in the field of numerical modeling and simulation of machining processes. The efficiency of the ...
Influence of lubrication condition on the surface integrity induced during drag finishing
(Elsevier Ltd, 2020)
Tribofinishing is one of the most popular polishing process in industry. The action of small abrasive media around parts enables to reduce significantly surface roughness and at the same time, to induce compressive residual ...
A Note on Interpreting Tool Temperature Measurements from Thermography
(Taylor & Francis, 2015)
Thermography (thermal imaging) is a well-established experimental method for studying cutting tool temperature distributions. In one form, cutting edge temperatures within the chip / tool contact area are deduced from ...
Evaluation of different flow stress laws coupled with a physical based ductile failure criterion for the modelling of the chip formation process of Ti-6Al-4V under broaching conditions
(Elsevier, 2019)
During the machining of Ti-6Al-4V the changing deformation mechanisms produce a complex microstructure of segmented chips, which directly influenced tool-wear and process stability. Numerical simulation could give an insight ...
Microstructural aspects of the transition between two regimes in orthogonal cutting of AISI 1045 steel
(Elsevier, 2018)
In depth understanding of tool-chip friction behavior is a significant aspect for tool wear performance in steels. In the present work attention has been paid to the strain mode of the chip section in contact with the rake ...
Influence of tool wear on residual stresses when turning Inconel 718
(Elsevier, 2016)
This paper analyzes the effect of tool wear on residual stresses when turning. Inconel 718 discs were machined for prolonged periods at several cutting speeds, feed-rates and depth of cut. Tests were interrupted to measure ...
Experimental investigation of contact forces and temperatures in rubbing interactions of honeycomb interstate seals
(IOP Publishing, 2021)
The new architecture of high velocity aircraft engines includes labyrinth-honeycomb interstate seals to improve the engine’s stability. To increase these engines capacity a commonly used strategy is to reduce the clearance ...
Analysis of the Tool Stick-Out Influence on Machining Chatter
(2021)
Increased stability in machining processes is highly desired by all machining industries when vibrations and specially chatter occur. This phenomenon is defined as a self-excited vibration that occurs due to the regeneration ...
Development and experimental validation of a macroscopic analytical model aiming to generate metal-FRP stacks drilling cutting force and torque
(2021)
Composites materials and especially FRP are increasingly employed in many fields of applications (transport, aerospace, …) due to the current trend of improving global energy performances of new designs notably by mass ...
Effect of surface integrity generated by machining on isothermal low cycle fatigue performance of Inconel 718
(Elsevier Ltd., 2022)
Critical aero-engine components such as turbine discs must withstand severe cyclic stresses, which can eventually lead to low cycle fatigue (LCF) failures. These components are made of difficult-to-cut alloys and machining ...
Surface roughness assessment on hole drilled through the identification and clustering of relevant external and internal signal statistical features
(Elsevier, 2022)
Drilling is a continuous cutting process where two or more cutting edges remove the material, to obtain the desired feature. During the chip evacuation, it generally rubs against the generated surface. Thus, the roughness ...
Experimental evaluation and surface integrity analysis of cryogenic coolants approaches in the cylindrical plunge grinding
(Nature Publishing Group, 2021)
Replacement of pollutant fuids with eco-friendly strategies in machining operations signifcantly contributes to protecting the environment, diminishing global warming, and ensuring a healthier workplace for employees. This ...
Sensor signal selection for tool wear curve estimation and subsequent tool breakage prediction in a drilling operation
(Taylor & Francis, 2021)
Tool condition monitoring have an important role in machining processes to reduce defective component and ensure quality requirements. Stopping the process before the tool breaks or an excessive tool wear is reached can ...
Hole quality improvement in CFRP/Ti6Al4V stacks using optimised flow rates for LCO2 and MQL sustainable cooling/lubrication
(Elsevier, 2024)
Carbon fibre reinforced polymer/titanium stacks (CFRP/Ti6Al4V) are employed in aeronautics due to their excellent weight-to-strength ratio and corrosion properties. However, these same material properties present challenges ...
Optimal manufacturing configuration selection: sequential decision making and optimization using reinforcement learning
(Elsevier, 2023)
In manufacturing, different costs must be considered when selecting the optimal manufacturing configuration. Costs include manufacturing costs, material costs, labor costs, and overhead costs. Optimal manufacturing ...
Application of material constitutive and friction models parameters identified with AI and ALE to a CEL orthogonal cutting model
(Elsevier B.V., 2023)
The identification of input parameters for funite element modelling of the cutting process is still a complex task as the experimental testing equipment cannot reach its combined levels of strains, strain rates and ...