Bilatu
29-tik 1-20 emaitza erakusten
Numerical simulation of U-Drawing test of Fortiform 1050 steel using different material models
(Elsevier Ltd., 2017)
Steel has been used in vehicles from the automotive industry's inception. Different steel grades are continually being developed
in order to satisfy new fuel economy requirements. For example, advanced high ...
Press hardening of alternative materials: conventional high- strength steels
(Springer Nature, 2017)
he increase in strength of new high strength steels(HHS) and advanced high strength steels (AHHS) has led toforming issues, such as high springback, low formability, increase of forming forces and tool wear. These problems ...
Study on the influence of the springback on the hole expansion ratio characterization
(Whioce Publishing, 2018)
Material formability has become one of the main problems, together with the springback, when stamping high
added-value components for the automotive industry. The pursuit of weight reduction has led to higher strength ...
Numerical simulation of the roll levelling of third generation fortiform 1050 steel using a nonlinear combined hardening material model
(IOP Publishing Ltd, 2017)
Elasto–plastic behavior of the third generation Fortiform 1050 steel has been analysed using cyclic tension–compression tests. At the same time, the pseudo elastic modulus evolution with plastic strain was analysed using ...
U-drawing of Fortiform 1050 third generation steels. Numerical and experimental results
(IOP Publishing Ltd, 2017)
Elasto–plastic behavior of the third generation Fortiform 1050 steel has been analysed using cyclic tension–compression tests. At the same time, the pseudo elastic modulus evolution with plastic strain was analysed using ...
Experimental and Numerical Simulation Investigation on Deep Drawing Process of Inconel 718 with and without Intermediate Annealing Thermal Treatments
(MDPI AG, 2020)
The aeronautical industry is moving from high-capacity large-airplane construction to low-capacity small-airplane construction. With the change in the production volume, there is a need for more e cient manufacturing ...
On the accurate characterization of the drawbead up-lift forces
(IOP Publishing Ltd., 2018)
The competitiveness of the automotive sector has led to a high demand of accuracy and reduction in lead-time of the deep drawing tool making process. In that regard, the numerical simulation of the deep drawing process has ...
Drawbead uplift force analytical model for deep drawing operations
(IOP Publishing Ltd., 2018)
Drawbead uplift force calculation has been an open issue among the deep drawing tool maker and software developers in the last years. Starting from the original work of Stoughton (1988) many have been the models presented ...
Roll levelling semi-analytical model for process optimization
(IOP, 2016)
Roll levelling is a primary manufacturing process used to remove residual stresses and imperfections of metal strips in order to make them suitable for subsequent forming operations. In the last years the importance of ...
Sensitivity analysis on an AC600 aluminum skin component
(IOP, 2016)
New materials are been introduced on the car body in order to reduce weight and fulfil the international CO2 emission regulations. Among them, the application of aluminum alloys is increasing for skin panels. Even if these ...
The influence of the kinematic hardening on the FEM simulation of Tension Levelling Process
(Elsevier Ltd., 2020)
Tension levelling is used in the steel industry to remove shape defects present in cold rolled strip. This technology is increasingly being employed by steel makers to level AHSS steels, because conventional roll levelers ...
The Interaction between the Sheet/Tool Surface Texture and the Friction/Galling Behaviour on Aluminium Deep Drawing Operations
(MDPI, 2021)
The increasing demands for lightweight design in the transport industry have led to an extensive use of lightweight materials such as aluminium alloys. The forming of aluminium sheets however presents significant challenges ...
Comparison of the hardening behaviour of different steel families : from mild and stainless steel to advanced high strength steels
(Elsevier Ltd., 2015)
Although steel has been used in vehicles from the automotive industry's inception, different steel gradesare continually being developed in order to satisfy new fuel economy requirements. For example,advanced high strength ...
Influence of the pressure dependent coefficient of friction on deep drawing springback predictions
(Elsevier Ltd., 2016)
The aim of this work is to show the influence of defining a pressure dependent friction coefficient onnumerical springback predictions of a DX54D mild steel, a HSLA380 and a DP780 high strength steel. Thepressure dependent ...
New drawbead tester and numerical analysis of drawbeads closure force
(Springer, 2021)
Currently, a great deal of controversy exists regarding the real forces generated in drawbeads during sheet metal forming processes. The present work focuses on the analysis of the uplift force. First, a detailed literature ...
Simulation of Cold Forging Processes Using a Mixed Isotropic-Kinematik Hardening Model
(Springer, 2021)
Cold forging is a manufacturing process where a bar stock is inserted into a die and squeezed with a second closed die. It is one of the most widely used chipless forming processes, often requiring no machining or additional ...
Substitutive Press-Bolster and Press-Ram Models for the Virtual Estimation of Stamping-Tool Cambering
(MDPI, 2021)
Today’s stamping simulations are realized by ignoring the elastic deformation of the press and tooling system through the assumption of a rigid behavior and a perfect press stroke. However, in reality, the press and tool ...
Contact pressure and sliding velocity ranges in sheet metal forming simulations
(2021)
In the last few years many efforts have been carried out in order to better understand what the real contact between material and tools is. Based on the better understanding new friction models have been developed which ...
Perfilado 4.0: ayuda a la puesta a punto y aseguramiento de la calidad en procesos de perfilado
(2019)
Una problemática a la que se enfrentan las empresas de perfilado de chapa es la laboriosa, y con ello costosa, puesta a punto del proceso. En ella los operarios basan sus decisiones en experiencias pasadas y en la mayoría ...
An automatic thermo-mechanical testing apparatus for metal forming applications
(Elsevier, 2023)
Dynamic testing of materials is necessary to model high-speed forming processes (e.g. hammer forging, blanking, forming, etc.) and crash/impact behaviour of structures, amongst others. The most common machines to perform ...