Zerrendatu honen arabera: izenburua
4890-tik 2389-2408 emaitza erakusten
-
Influence of Surface Finish and Porosity on the Fatigue behaviour of A356 Aluminium Casting Alloy
(EDP Sciences, 2018)In casting parts, due to the manufacturing process, the presence of defects such as porosity, inclusions and oxide films is unavoidable. All these irregularities have a negative effect on the component ... -
The influence of the kinematic hardening on the FEM simulation of Tension Levelling Process
(Elsevier Ltd., 2020)Tension levelling is used in the steel industry to remove shape defects present in cold rolled strip. This technology is increasingly being employed by steel makers to level AHSS steels, because conventional roll levelers ... -
Influence of the pressure dependent coefficient of friction on deep drawing springback predictions
(Elsevier Ltd., 2016)The aim of this work is to show the influence of defining a pressure dependent friction coefficient onnumerical springback predictions of a DX54D mild steel, a HSLA380 and a DP780 high strength steel. Thepressure dependent ... -
Influence of the test-chamber shape on the performance of conductometric gas sensors
(Elsevier, 2022)In this article, CFD simulations results are presented as a key tool to the comprehension of the target gas concentration evolution in a test chamber, at different working conditions. The simulation results are compared ... -
Influence of the velocity on quasi-static deflections of industrial articulated robots
(Springer, 2023)This article presents the measurement and analysis of the influence of velocity on the quasi-static deflections of industrial manipulators of three different manufacturers. Quasi-static deflection refers to the deflection ... -
Influence of tool wear on residual stresses when turning Inconel 718
(Elsevier, 2016)This paper analyzes the effect of tool wear on residual stresses when turning. Inconel 718 discs were machined for prolonged periods at several cutting speeds, feed-rates and depth of cut. Tests were interrupted to measure ... -
Influences of Cutting Speed and Material Constitutive Models on Chip Formation and their Effects on the Results of Ti6Al4V Orthogonal Cutting Simulation
(2021)The highly used Ti6Al4V alloy is a well know hard-to-machine material. The modelling of orthogonal cutting process of Ti6Al4V attract the interest of many researchers as it often generates serrated chips. The purpose of ... -
Influencia de la frecuencia respiratoria inducida en los valores HRV
(Servicio Editorial de la Universidad del País VascoEuskal Herriko Unibertsitateko Argitalpen Zerbitzua, 2017)The study of Place Cells, hippocampal neurons tuned to spatial locations in the environment, is central to elucidate how the brain encodes and retrieves spatial information. Advances in genetic and imaging technologies ... -
Influencia de la velocidad de impacto en la delaminación generada por impactos transversales de baja velocidad en tejidos carbono-epoxi. Dependencia del comportamiento interlaminar del composite a la velocidad de propagación de grieta
(Mondragon Unibertsitatea. Goi Eskola Politeknikoa, 2014)Los composites de matriz polimérica reforzados con tejido son materiales que por sus excelentes propiedades mecánicas específicas están llamados a ocupar un papel importante en el aligeramiento, necesario para reducir ... -
Influencia de los datos biográficos y experiencia deportiva de los estudiantes universitarios de educación fisíco-deportiva sobre sus creencias, actitudes y autoconcepto físico
(University of Almeria, 2023-03-06)El propósito de este estudio fue examinar cómo influyen las experiencias deportivas y su biografía en cada sujeto, con respecto a sus creencias y actitudes de cara a la educación física y su autoconcepto físico. Se utilizaron ... -
Influencia del agua de mar en el comportamiento frente a impacto de baja energía de un nuevo laminado de resina natural reforzada con fibra de fique colombiano
(Universidad Nacional de Colombia, 2015)This experimental work is aimed at the influence of seawater immersion in low impact energy behavior of a novel Colombian fique fiber reinforced bio-resin laminate. Such material was manufactured by vacuum infusion. The ... -
Infoday JTI ECSEL
(Mondragon Unibertsitatea, 2015-04-16)MINETUR, MINECO eta CDTIek Bartzelonako Mikroelektonikako Zentro Nazionalarekin elkarlanean, Infoday ECSEL- Bartzelonako Mikroelektonikako Zentro Nazionalaren 2015eko deialdia jardunaldia antolatu zuten martxoan deialdiari ... -
Informatika sistemen kudeatzailea behar da
(Mondragon Unibertsitatea, 2012-10-01)Mondragon Unibertsitatearen Humanitate eta Hezkuntza Zientzien Fakultateak, HUHEZIk, berehala eta aldi baterako lanean hasteko informatika sistemen (erabiltzaileak, zerbitzariak,…) kudeatzailea behar du, Teknologi Zerbitzuak ... -
Informazio baliabide berria Bibliotekan: ASM argitaletxearen bilduma elektronikoak
(Mondragon Unibertsitatea, 2014-10-14) -
Informazio baliabide berria, EEUUko Zientziaren Atari Federala
(Mondragon Unibertsitatea, 2012-11-27)Bibliotekak informazio baliabide berria eskeintzen dizu, Zientziaren Atari Federalaren berstio berria gaztelaniaz -
Informazio baliabide berria: Automobilgintza Hiztegi espezializatua
(Mondragon Unibertsitatea, 2014-07-09) -
Informazio baliabide berria: Diccionario Español de Ingeniería
(Mondragon Unibertsitatea, 2014-04-29) -
Informazio saioak Hezkuntzako master, gradu modalitate erdi-presentzialean eta aditu tituluei buruzkoak, ekainaren 15ean, Eskoriatza eta Aretxabaletako campusetan
(Mondragon Unibertsitatea, 2017-06-06)Ekainaren 15ean, osteguna, informazio saioak egingo dira Humanitate eta Hezkuntza Zientzien Fakultatean argibideak emateko hezkuntzako Master, Gradu modalitate erdi-presentzialean eta zenbait Aditu Tituluen gainean. ... -
Informazio Sistemak taldeak blog bat sortu du, informazioa partekatzeko
(Mondragon Unibertsitatea, 2009-10-19) -
Informazioa irakasle gradurako egokitze kurtsoaz
(Mondragon Unibertsitatea, 2012-07-04)Uztailaren 4a eta 6a bitartean ikasleen onarpen prozesua aurrera eramango da Irakasleentzako Gradurako Egokitze Kurtsoetan. Prozesu horren barruan, hautatze-irizpideen arabera eguneratzen joango dira ikasleen egoerak; hauek ...
