Erregistro soila

dc.rights.licenseAttribution-NonCommercial-NoDerivatives 4.0 International*
dc.contributor.authorCUESTA ZABALAJAUREGUI, MIKEL
dc.contributor.authorOrtiz-de-Zarate, Gorka
dc.contributor.authorSáenz de Argandoña, Eneko
dc.contributor.authorSoriano Moreno, Denis
dc.contributor.authorARRAZOLA, PEDRO JOSE
dc.contributor.otherMadariaga Zabala, Aitor
dc.contributor.otherPrime, Michael B.
dc.date.accessioned2024-04-29T13:37:40Z
dc.date.available2024-04-29T13:37:40Z
dc.date.issued2023
dc.identifier.issn1000-9361en
dc.identifier.otherhttps://katalogoa.mondragon.edu/janium-bin/janium_login_opac.pl?find&ficha_no=174223en
dc.identifier.urihttps://hdl.handle.net/20.500.11984/6384
dc.description.abstractThin-walled aerostructural components frequently get distorted after the machining process. Reworking to correct distortions or eventually rejecting parts significantly increases the cost. This paper proposes a new approach to correct distortions in thin-walled components by strategically applying hammer peening on target surfaces of a machined component. Aluminium alloy 7475-T7351 was chosen for this research. The study was divided in two stages. First, the residual stresses (RS) induced by four different pneumatic hammer peening conditions (modifying the stepover distance and initial offset) were characterised in a test coupon, and one of the conditions was selected for the next stage. In the second stage, a FEM model was used to predict distortions caused by machining in a representative workpiece. Then, the RS induced by hammer peening were included in an FEM model to define two hammer peening strategies (varying the coverage area) to analyse the capability to reduce distortions. Two workpieces were machined and then treated with the simulated hammer peening strategies for experimental validation. Results in the test coupon showed that pneumatic hammer peening can generate high compressive RS (-50 to −350 MPa) up to 800 μm depth, with their magnitude increasing with a reduced stepover distance. Application of hammer peening over 4 % of the surface of the representative workpiece reduced the machining-induced distortions by 37 %, and a coverage area of 100 % led to and overcorrection by a factor of five. This confirms that hammer peening can be strategically applied (in target areas and changing the percentage of coverage) to correct low or severe distortions.en
dc.language.isoengen
dc.publisherElsevieren
dc.rights© 2023 Chinese Society of Aeronautics and Astronauticsen
dc.rights.urihttp://creativecommons.org/licenses/by-nc-nd/4.0/*
dc.subjectAeronauticsen
dc.subjectMachiningen
dc.subjectHammer peeningen
dc.subjectaluminium alloysen
dc.subjectDistortionsen
dc.subjectResidual stressen
dc.titleCorrecting distortions of thin-walled machined parts by machine hammer peeningen
dcterms.accessRightshttp://purl.org/coar/access_right/c_abf2en
dcterms.sourceChinese Journal of Aeronauticsen
local.contributor.groupMecanizado de alto rendimientoes
local.description.peerreviewedtrueen
local.identifier.doihttps://doi.org/10.1016/j.cja.2023.10.023en
local.contributor.otherinstitutionhttps://ror.org/027m9bs27en
local.contributor.otherinstitutionhttps://ror.org/01e41cf67
local.source.detailsVol. 37. N. 6. Pp. 439-453. June, 2024
oaire.format.mimetypeapplication/pdfen
oaire.file$DSPACE\assetstoreen
oaire.resourceTypehttp://purl.org/coar/resource_type/c_6501en
oaire.versionhttp://purl.org/coar/version/c_ab4af688f83e57aaen


Item honetako fitxategiak

Thumbnail
Thumbnail

Item hau honako bilduma honetan/hauetan agertzen da

Erregistro soila

Attribution-NonCommercial-NoDerivatives 4.0 International
Bestelakorik adierazi ezean, itemaren baimena horrela deskribatzen da: Attribution-NonCommercial-NoDerivatives 4.0 International