Zerrendatu Artikuluak-Ingeniaritza honen arabera: izenburua
578-tik 285-304 emaitza erakusten
-
Influence of lubrication condition on the surface integrity induced during drag finishing
(Elsevier Ltd, 2020)Tribofinishing is one of the most popular polishing process in industry. The action of small abrasive media around parts enables to reduce significantly surface roughness and at the same time, to induce compressive residual ... -
Influence of manufacturing tolerances and eccentricities on the unbalanced magnetic pull in permanent magnet synchronous motors
(IEEE, 2022)Eccentricity is an inevitable fault in electric motors and hence its diagnosis is an important topic. Thus, the influence of static and dynamic eccentricities on the harmonics of the frequency spectra of the unbalanced ... -
Influence of Microstructure on Chip Formation when Broaching Ferritic-Pearlitic Steels
(Elsevier B.V., 2017)Broaching is a specific process characterized by relatively low cutting speeds and uncut chip thicknesses. The latter is in the range of 0.1 to 0.25 mm in the roughing section of the tool but can decrease down to 0.0015 ... -
Influence of nanoparticles morphology in magnetic fluids
(Elsevier, 2024)In this work magnetic fluids at two different volume concentrations (5 % and 10 %) of magnetite nanoparticles of different morphologies and sizes (octahedral, 38 ± 5 nm; truncated octahedral, 10 ± 1 nm; rod-like, 95 nm x ... -
The influence of the kinematic hardening on the FEM simulation of Tension Levelling Process
(Elsevier Ltd., 2020)Tension levelling is used in the steel industry to remove shape defects present in cold rolled strip. This technology is increasingly being employed by steel makers to level AHSS steels, because conventional roll levelers ... -
Influence of the pressure dependent coefficient of friction on deep drawing springback predictions
(Elsevier Ltd., 2016)The aim of this work is to show the influence of defining a pressure dependent friction coefficient onnumerical springback predictions of a DX54D mild steel, a HSLA380 and a DP780 high strength steel. Thepressure dependent ... -
Influence of the test-chamber shape on the performance of conductometric gas sensors
(Elsevier, 2022)In this article, CFD simulations results are presented as a key tool to the comprehension of the target gas concentration evolution in a test chamber, at different working conditions. The simulation results are compared ... -
Influence of the velocity on quasi-static deflections of industrial articulated robots
(Springer, 2023)This article presents the measurement and analysis of the influence of velocity on the quasi-static deflections of industrial manipulators of three different manufacturers. Quasi-static deflection refers to the deflection ... -
Influencia del agua de mar en el comportamiento frente a impacto de baja energía de un nuevo laminado de resina natural reforzada con fibra de fique colombiano
(Universidad Nacional de Colombia, 2015)This experimental work is aimed at the influence of seawater immersion in low impact energy behavior of a novel Colombian fique fiber reinforced bio-resin laminate. Such material was manufactured by vacuum infusion. The ... -
An Innovative Energy Harvesting Shock Absorber System for Motorbikes
(IEEE, 2022)This article presents an innovative energy recovery shock absorber system for motorcycles. The shock absorber is named synchronous pulley - energy harvesting shock absorber (SP-EHSA). The SP-EHSA is the first system ... -
Integral Sensor Fault Detection and Isolation for Railway Traction Drive
(MDPI AG, 2018)Due to the increasing importance of reliability and availability of electric traction drives in Railway applications, early detection of faults has become an important key for Railway traction drive manufacturers. Sensor ... -
An integrated inverse numerical–experimental approach to determine the dynamic Mode-I interlaminar fracture toughness of fibre composites
(Elsevier, 2022)A combined numerical–experimental methodology is presented to determine the dynamic Mode-I fracture properties of Fibre-Reinforced Polymer (FRP) composites. The experimental aspect consists of a modified Wedge-Double ... -
Integrated machine learning and probabilistic degradation approach for vessel electric motor prognostics
(Elsevier, 2023)In the transition towards more sustainable ships, electric motors (EM) are being used in ship propulsion systems to reduce emissions and increase efficiency. The safe operation of ships is crucial, and prognostics and ... -
Integration of Hot Isostatic Pressing and Heat Treatment for Advanced Modified gamma-TiAl TNM Alloys
(MDPI, 2022)The conventional processing route of TNM (Ti-Nb-Mo) alloys combines casting and Hot Isostatic Pressing (HIP) followed by forging and multiple heat treatments to establish optimum properties. This is a time-consuming and ... -
The Interaction between the Sheet/Tool Surface Texture and the Friction/Galling Behaviour on Aluminium Deep Drawing Operations
(MDPI, 2021)The increasing demands for lightweight design in the transport industry have led to an extensive use of lightweight materials such as aluminium alloys. The forming of aluminium sheets however presents significant challenges ... -
Inverse Identification of the Ductile Failure Law for Ti6Al4V Based on Orthogonal Cutting Experimental Outcomes
(MDPI, 2021)Despite the prevalence of machining, tools and cutting conditions are often chosen based on empirical databases, which are hard to be made, and they are only valid in the range of conditions tested to develop it. Predictive ... -
Investigating the performance of 410, PH13-8Mo and 300M steelsin a turning process with a focus on surfacefinish
(Elsevier Ltd., 2020)This study generated novel behavioural data for three engineering steels undergoing a turning process. The materialswere hardened 410, PH13-8Mo and 300M, two stainless steels and one high strength steel respectively. A ... -
Investigation of diffusive and optical properties of vapour-air mixtures: The benefits of interferometry
(Elsevier Ltd., 2021)While interferometry has been widely used for diffusion measurements in liquid mixtures, it was hardly applied so far to vapour-gas mixtures. The present work aims to bridge this gap. Using an improved Mach–Zehnder ... -
Investigation of Microservice-Based Workflow Management Solutions for Industrial Automation
(MDPI, 2023)In an era ruled by data and information, engineers need new tools to cope with the increased complexity of industrial operations. New architectural models for industry enable open communication environments, where workflows ...
