Zerrendatu Ikerketa-Artikuluak honen arabera: izenburua
705-tik 195-214 emaitza erakusten
-
The effect of cross-section geometry on crushing behaviour of 3D printed continuous carbon fibre reinforced polyamide profiles
(Elsevier, 2021)The present study has analysed the effect of cross-section geometry and the printing pattern of continuous carbon reinforced polyamide on the axial and radial crushing behaviour. Each geometry and printing pattern generated ... -
Effect of cutting speed on the surface integrity of face milled 7050-T7451 aluminium workpieces
(Elsevier Ltd., 2018)The guarantee of surface integrity has become a primary objective for researchers when analysing the reliability of machined aircraft aluminium alloy structural parts in high-speed machining. This work studies the effect ... -
The effect of high involvement work systems on organisational performance and employee well-being in a Spanish industrial context
(Wiley, 2022-03)This study investigates whether employee perceptions of High Involvement Work Systems (HIWS) mediate the positive relationship between implemented-HIWS and the parallel outcomes of employee well-being and organisational ... -
Effect of liner thermal properties and liner pre-cooling on the thermal management of fast-filling of hydrogen tanks
(Elsevier, 2023)In transportation applications, filling high pressurised hydrogen tanks within a few minutes implies a fast and large temperature increase that can compromise the structural integrity of the storage system and the safety ... -
Effect of Post-Processing Treatment on Fatigue Performance of Ti6Al4V Alloy Manufactured by Laser Powder Bed Fusion
(MDPI, 2023)Fatigue properties of parts are of particular concern for safety-critical structures. It is well-known that discontinuities in shape or non-uniformities in materials are frequently a potential nucleus of fatigue failure. ... -
The effect of small perturbation on dynamics of absorptive LiBr–water solution
(AIP Publishing, 2024)In a binary solution of lithium bromide–water, even a small disturbance in the initial homogeneous mass fraction at the absorbing interface has profound effects on the entire system dynamics. This perturbation of absorption ... -
Effect of surface integrity generated by machining on isothermal low cycle fatigue performance of Inconel 718
(Elsevier Ltd., 2022)Critical aero-engine components such as turbine discs must withstand severe cyclic stresses, which can eventually lead to low cycle fatigue (LCF) failures. These components are made of difficult-to-cut alloys and machining ... -
Effect of the crucible composition on the Inconel 718 vacuum induction melting process efficiency
(Elsevier, 2023)Nickel-based superalloys are widely employed to manufacture aero-engine turbines due to their high mechanical strength and resistance to corrosion and creep. Vacuum Induction Melting (VIM) is a suitable manufacturing ... -
Effect of Tool Geometry and LCO2 Cooling on Cutting Forces and Delamination when Drilling CFRP Composites Using PCD Tools
(Elsevier, 2022)Lightweight materials like Carbon Fiber Reinforced Polymers (CFRPs) present certain challenges, mainly regarding the resultant surface integrity of the holes. Different techniques such as optimized tool geometries, machining ... -
Effect of voids on the impact properties of Non-Crimp fabric carbon/epoxy laminates manufactured by liquid composite Moulding
(Elsevier, 2022)A great effort has been made to quantify the detrimental effect of voids on CFRP, nevertheless, the effect on impact properties has been barely studied and when it has been considered, it has always been for prepeg materials ... -
Effects of Different Si Content and Thermal Stories on the Secondary Phase Formation, Hot Ductility, and Stress Rupture Properties of Alloy 718 Investment Castings
(Springer, 2023)Herein, the effects of microstructure on high-temperature properties (hot ductility and stress rupture life) were investigated in alloy 718 investment castings manufactured with different Si contents (0.051, 0.11, and 0.17 ... -
Effects of manufacturing tolerances of permanent magnets in fractional slot permanent magnet synchronous machines
(IET, 2019)The fractional slot permanent magnet synchronous machines are well-known for their low torque ripple. However, in mass-production machines, not all the permanent magnets are identical due to the manufacturing tolerances ... -
Effects of Socioeconomic Environment on Physical Activity Levels and Sleep Quality in Basque Schoolchildren
(MDPI, 2023)The socioeconomic and built environment of an area are interrelated with health data and have a direct influence on children’s development. There are facilitators and barriers for schools to promote physical activity ... -
Efficient Calculation of Stabilization Parameters in RF Power Amplifiers
(IEEE, 2020)This paper proposes an efficient method for the calculation of the stabilization parameters in RF power amplifiers operating in periodic large-signal regimes. Stabilization is achieved by applying the principles of linear ... -
Ekintzailetza sozial kooperatiboa: KoopFabrika egitasmoaren kasua
(Universidad del País Vasco = Euskal Herriko Unibertsitatea, 2019)Ekintzailetza soziala azken urteotan bogan dagoen praktika bat da. Berrikuntza sozial, ekonomia sozial eta enpresa sozial kontzeptuekin gertatzen den hantzera, ekintzailetza soziala ulertu eta praktikatzeko joera ezberdinak ... -
Elastic behaviour characterisation of TRIP 700 steel by means of loading-unloading tests
(Elsevier Ltd., 2015)The elastic behaviour of TRIP 700 steel under plastic deformation is analysed. The analysis is carried out by means of classical tensile test and loading–unloading cyclic tests. These tests have been performed using high ... -
Electric Technology in Wind Turbines from a Dialectic Perspective
(Philosophy Documentation Center, 2019)Wind turbines have been used by many groups of humans for many centu-ries. Wind turbines have allowed groups of humans to perform many different tasks in the past (grinding grain, pumping water, etc.). However, ... -
Electric Vehicle Inverter Electro-Thermal Models Oriented to Simulation Speed and Accuracy Multi-Objective Targets
(MDPI AG, 2019)With the increasing demand for electric vehicles, the requirements of the market are changing ever faster. Therefore, there is a need to improve the electric car’s design time, where simulations could be an appropriate ... -
Electrochemical Model and Sigma Point Kalman Filter Based Online Oriented Battery Model
(IEEE, 2021)This paper presents a reduced-order electrochemical battery model designed for online implementation of battery control systems. This model is based on porous-electrode and concentratedsolution theory frameworks and is ... -
Electromechanical Properties of PVDF-Based Polymers Reinforced with Nanocarbonaceous Fillers for Pressure Sensing Applications
(MDPI AG, 2019)Polymer-based composites reinforced with nanocarbonaceous materials can be tailored for functional applications. Poly(vinylidene fluoride) (PVDF) reinforced with carbon nanotubes (CNT) or graphene with different filler ...
