Zerrendatu Artikuluak-Ingeniaritza honen arabera: izenburua
592-tik 289-308 emaitza erakusten
-
Influence of Al addition on microstructure and electrochemical behaviour of CrMnFeCoNi high-entropy alloy
(Elsevier, 2024)To develop new corrosion-resistant materials for structural applications, CrMnFeCoNiAlx high-entropy alloys (HEAs) are produced via semi-industrial induction casting. The study aimed to investigate the influence of Al ... -
Influence of Coulomb’s Friction Coefficient in Finite Element Modeling of Orthogonal Cutting of Ti6Al4V
(Trans Tech Publications, 2022)The reliability of the pertinent parameters set of Johnson-Cook constitutive model is highly linked with the friction condition at the tool-chip-workpiece interface. In the present work, a study on the influence of Coulomb’s ... -
Influence of cryogenic grinding surface on fatigue performance of carburised 27MnCr5
(Elsevier, 2023)Automotive transmission components are subjected to cyclic loads and, thus, must have a reliable fatigue performance. Since fatigue cracks nucleate at the surface, it is necessary to guarantee that its surface integrity ... -
Influence of lubrication condition on the surface integrity induced during drag finishing
(Elsevier Ltd, 2020)Tribofinishing is one of the most popular polishing process in industry. The action of small abrasive media around parts enables to reduce significantly surface roughness and at the same time, to induce compressive residual ... -
Influence of manufacturing tolerances and eccentricities on the unbalanced magnetic pull in permanent magnet synchronous motors
(IEEE, 2022)Eccentricity is an inevitable fault in electric motors and hence its diagnosis is an important topic. Thus, the influence of static and dynamic eccentricities on the harmonics of the frequency spectra of the unbalanced ... -
Influence of Microstructure on Chip Formation when Broaching Ferritic-Pearlitic Steels
(Elsevier B.V., 2017)Broaching is a specific process characterized by relatively low cutting speeds and uncut chip thicknesses. The latter is in the range of 0.1 to 0.25 mm in the roughing section of the tool but can decrease down to 0.0015 ... -
Influence of nanoparticles morphology in magnetic fluids
(Elsevier, 2024)In this work magnetic fluids at two different volume concentrations (5 % and 10 %) of magnetite nanoparticles of different morphologies and sizes (octahedral, 38 ± 5 nm; truncated octahedral, 10 ± 1 nm; rod-like, 95 nm x ... -
The influence of the kinematic hardening on the FEM simulation of Tension Levelling Process
(Elsevier Ltd., 2020)Tension levelling is used in the steel industry to remove shape defects present in cold rolled strip. This technology is increasingly being employed by steel makers to level AHSS steels, because conventional roll levelers ... -
Influence of the pressure dependent coefficient of friction on deep drawing springback predictions
(Elsevier Ltd., 2016)The aim of this work is to show the influence of defining a pressure dependent friction coefficient onnumerical springback predictions of a DX54D mild steel, a HSLA380 and a DP780 high strength steel. Thepressure dependent ... -
Influence of the test-chamber shape on the performance of conductometric gas sensors
(Elsevier, 2022)In this article, CFD simulations results are presented as a key tool to the comprehension of the target gas concentration evolution in a test chamber, at different working conditions. The simulation results are compared ... -
Influence of the velocity on quasi-static deflections of industrial articulated robots
(Springer, 2023)This article presents the measurement and analysis of the influence of velocity on the quasi-static deflections of industrial manipulators of three different manufacturers. Quasi-static deflection refers to the deflection ... -
Influencia del agua de mar en el comportamiento frente a impacto de baja energía de un nuevo laminado de resina natural reforzada con fibra de fique colombiano
(Universidad Nacional de Colombia, 2015)This experimental work is aimed at the influence of seawater immersion in low impact energy behavior of a novel Colombian fique fiber reinforced bio-resin laminate. Such material was manufactured by vacuum infusion. The ... -
An Innovative Energy Harvesting Shock Absorber System for Motorbikes
(IEEE, 2022)This article presents an innovative energy recovery shock absorber system for motorcycles. The shock absorber is named synchronous pulley - energy harvesting shock absorber (SP-EHSA). The SP-EHSA is the first system ... -
Integral Design and Manufacturing Methodology of a Reduced-Scale Servo Press
(IEEE, 2021)In a context where industrial production boosts both the society and the economy of a country, improvements in industrial processes are key factors for efficient and reliable development of goods and products. New industrial ... -
Integral Sensor Fault Detection and Isolation for Railway Traction Drive
(MDPI AG, 2018)Due to the increasing importance of reliability and availability of electric traction drives in Railway applications, early detection of faults has become an important key for Railway traction drive manufacturers. Sensor ... -
An integrated inverse numerical–experimental approach to determine the dynamic Mode-I interlaminar fracture toughness of fibre composites
(Elsevier, 2022)A combined numerical–experimental methodology is presented to determine the dynamic Mode-I fracture properties of Fibre-Reinforced Polymer (FRP) composites. The experimental aspect consists of a modified Wedge-Double ... -
Integrated machine learning and probabilistic degradation approach for vessel electric motor prognostics
(Elsevier, 2023)In the transition towards more sustainable ships, electric motors (EM) are being used in ship propulsion systems to reduce emissions and increase efficiency. The safe operation of ships is crucial, and prognostics and ... -
Integration of Hot Isostatic Pressing and Heat Treatment for Advanced Modified gamma-TiAl TNM Alloys
(MDPI, 2022)The conventional processing route of TNM (Ti-Nb-Mo) alloys combines casting and Hot Isostatic Pressing (HIP) followed by forging and multiple heat treatments to establish optimum properties. This is a time-consuming and ... -
The Interaction between the Sheet/Tool Surface Texture and the Friction/Galling Behaviour on Aluminium Deep Drawing Operations
(MDPI, 2021)The increasing demands for lightweight design in the transport industry have led to an extensive use of lightweight materials such as aluminium alloys. The forming of aluminium sheets however presents significant challenges ...
