Zerrendatu Artikuluak-Ingeniaritza honen arabera: izenburua
579-tik 118-137 emaitza erakusten
-
Design and 3D printing of an electrochemical sensor for Listeria monocytogenes detection based on loop mediated isothermal amplification
(Elsevier, 2023)The aim of this work is the design and 3D printing of a new electrochemical sensor for the detection of Listeria monocytogenes based on loop mediated isothermal amplification (LAMP). The food related diseases involve a ... -
Design and characterisation of cellular composite structures for automotive crashboxes manufactured by out of die ultraviolet cured pultrusion
(Elsevier B.V., 2019-03-01)The present paper analyses the feasibility of designing a honeycomb-like crash-box, as a cellular structure, based on data obtained from the characterisation of the building block. In order to generalise the conclusions ... -
Design and characterization of a novel lightweight multicomponent alloy Al58Zn28Mg6Si8
(Elsevier, 2023)This paper presents a novel multicomponent alloy Al58Zn28Mg6Si8, with a density of 3.46 g/cm3, which incorporates concepts from high entropy alloys. The optimum alloy composition was determined using the CALPHAD approach ... -
Design of a Radiant Heat Capturing Device for Steel Mills
(International Centre for Sustainable Development of Energy, Water and Environment Systems, 2021)This paper approaches the energy transition towards decarbonization and lower primary energy use in the steel and glass industries through the exploitation of radiant waste heat. In contrast with exhaust gases heat recovery, ... -
Design of a Solid-State Circuit Breaker for a DC Grid-Based Vessel Power System
(MDPI, 2019)Electric propulsion and integrated hybrid power systems can improve the energy efficiency and fuel consumption of different kinds of vessels. If the vessel power system is based on DC grid distribution, some benefits ... -
Design Space Analysis of the Dual-Active-Bridge Converter for More Electric Aircraft
(MDPI, 2022)In the literature, different DC/DC power electronic converters (PECs) have been found to interconnect high-voltage DC and low-voltage DC grids in the electric power distribution networks of aircraft. In this scenario, the ... -
A Design Thinking approach to introduce entrepreneurship education in European school curricula
(Taylor & Francis, 2017)Design Thinking is visualized as the central strategy to promote entrepreneurial skills in European schools. Europe needs future generations to be more entrepreneurial in their attitudes to achieve a strong position in the ... -
Design to cost; a framework for large industrial products
(Elsevier Ltd., 2021)A literature review on the assembly design methodologies (DfA) oriented to the assembly of large and heavy parts, reveals the need to develop a DfA methodology. In addition, the lack of DfA evaluation methods for on-site ... -
Designing for Shape Memory in Additive Manufacturing of Cu–Al–Ni Shape Memory Alloy Processed by Laser Powder Bed Fusion
(MDPI, 2022)Shape memory alloys (SMAs) are functional materials that are being applied in practically all industries, from aerospace to biomedical sectors, and at present the scientific and technologic communities are looking to gain ... -
Designing the Process for Implementing Step Three of the Theory of Constraints in a Make-To-Order Environment: Integrating Sales and Operation Planning
(OmniaScience, 2023)Purpose: The theory of constraints (TOC) methodology and its drum-buffer-rope (DBR) production planning and control system are well suited to managing production plants in complex environments. The objective of this study ... -
Detection and Visualization of Android Malware Behavior
(Hindawi Publishing Corporation, 2016)Malware analysts still need to manually inspect malware samples that are considered suspicious by heuristic rules. They dissect software pieces and look for malware evidence in the code. The increasing number of malicious ... -
Determination of emissivity and temperature of tool rake face when cutting AISI 4140
(Elsevier B.V., 2019)A method for measuring tool temperature in the tool/chip contact zone of the rake face of a tool during dry orthogonal cutting using thermography is presented. This method used a new calibration method that combined with ... -
Determination of molecular diffusion coefficient in n-Alkane binary mixtures: empirical correlations
(ACS Publishing, 2012)In this work we have measured the molecular diffusion coefficient of the n-alkane binary series nCi-nC6, nCi-nC10, and nCi-nC12 at 298 K and 1 atm and a mass fraction of 0.5 by using the so-called sliding symmetric tubes ... -
Determination of the molecular diffusion coefficients in ternary mixtures by the sliding symmetric tubes technique
(AIP Publishing, 2014)A new analytical methodology has been developed to determine the diagonal and cross-diagonal molecular diffusion coefficients in ternary mixtures by the Sliding Symmetric Tubes technique. The analytical solution is tested ... -
Determining tool/chip temperatures from thermography measurements in metal cutting
(Elsevier, 2018)Temperature measurement in metal cutting is of central importance as tool wear and surface integrity have been demonstrated to be temperature dependent. In this context, infrared thermography is presented as a reliable ... -
Development and Comparison of Rule- and Machine Learning-Based EMS for HESS Providing Grid Services
(IEEE, 2024)In this paper, a smart machine-learning-based energy management system (MLBEMS) is developed for a hybrid energy storage system (HESS). This HBESS consists of batteries with high-energy (HE) and high-power (HP) characteristics, ... -
Development and validation of a tool for the integration of the circular economy in industrial companies
(Elsevier, 2022)Circular Economy (CE) implementation is considered an instrumental strategy to help reaching the world's resource, energy, and climate mitigation targets, including the Sustainable Development Goals (SDGs) 2030. However, ... -
Development and validation of an automatic manufacturing process for fiberglass composites
(Dyna Publishing, 2023)Fiberglass reinforced polymeric composites are ideal for various applications due to their mechanical properties and lightweight. However, nowadays many fiberglass reinforced composite manufacturing processes are manual, ... -
Development of a Modular Fretting Wear and Fretting Fatigue Tribometer for Thin Steel Wires: Design Concept and Preliminary Analysis of the Effect of Crossing Angle on Tangential Force
(MDPI AG, 2019)This work presents the design of a modular ad-hoc fretting fatigue and fretting wear tribotester for thin steel wires. The working principles of the diffrent modules are described, such as the displacement and contact ...
