Zerrendatu Ikerketa-Artikuluak honen arabera: izenburua
731-tik 362-381 emaitza erakusten
-
Influence of lubrication condition on the surface integrity induced during drag finishing
(Elsevier Ltd, 2020)Tribofinishing is one of the most popular polishing process in industry. The action of small abrasive media around parts enables to reduce significantly surface roughness and at the same time, to induce compressive residual ... -
Influence of manufacturing tolerances and eccentricities on the unbalanced magnetic pull in permanent magnet synchronous motors
(IEEE, 2022)Eccentricity is an inevitable fault in electric motors and hence its diagnosis is an important topic. Thus, the influence of static and dynamic eccentricities on the harmonics of the frequency spectra of the unbalanced ... -
Influence of Microstructure on Chip Formation when Broaching Ferritic-Pearlitic Steels
(Elsevier B.V., 2017)Broaching is a specific process characterized by relatively low cutting speeds and uncut chip thicknesses. The latter is in the range of 0.1 to 0.25 mm in the roughing section of the tool but can decrease down to 0.0015 ... -
Influence of nanoparticles morphology in magnetic fluids
(Elsevier, 2024)In this work magnetic fluids at two different volume concentrations (5 % and 10 %) of magnetite nanoparticles of different morphologies and sizes (octahedral, 38 ± 5 nm; truncated octahedral, 10 ± 1 nm; rod-like, 95 nm x ... -
The influence of the kinematic hardening on the FEM simulation of Tension Levelling Process
(Elsevier Ltd., 2020)Tension levelling is used in the steel industry to remove shape defects present in cold rolled strip. This technology is increasingly being employed by steel makers to level AHSS steels, because conventional roll levelers ... -
Influence of the pressure dependent coefficient of friction on deep drawing springback predictions
(Elsevier Ltd., 2016)The aim of this work is to show the influence of defining a pressure dependent friction coefficient onnumerical springback predictions of a DX54D mild steel, a HSLA380 and a DP780 high strength steel. Thepressure dependent ... -
Influence of the test-chamber shape on the performance of conductometric gas sensors
(Elsevier, 2022)In this article, CFD simulations results are presented as a key tool to the comprehension of the target gas concentration evolution in a test chamber, at different working conditions. The simulation results are compared ... -
Influence of the velocity on quasi-static deflections of industrial articulated robots
(Springer, 2023)This article presents the measurement and analysis of the influence of velocity on the quasi-static deflections of industrial manipulators of three different manufacturers. Quasi-static deflection refers to the deflection ... -
Influencia de los datos biográficos y experiencia deportiva de los estudiantes universitarios de educación fisíco-deportiva sobre sus creencias, actitudes y autoconcepto físico
(University of Almeria, 2023-03-06)El propósito de este estudio fue examinar cómo influyen las experiencias deportivas y su biografía en cada sujeto, con respecto a sus creencias y actitudes de cara a la educación física y su autoconcepto físico. Se utilizaron ... -
Influencia del agua de mar en el comportamiento frente a impacto de baja energía de un nuevo laminado de resina natural reforzada con fibra de fique colombiano
(Universidad Nacional de Colombia, 2015)This experimental work is aimed at the influence of seawater immersion in low impact energy behavior of a novel Colombian fique fiber reinforced bio-resin laminate. Such material was manufactured by vacuum infusion. The ... -
Innovación y cambio en la Formación Profesional del País Vasco. El modelo ETHAZI
(Organización de Estados Iberoamericanos, 2017)Los cambios económicos, productivos y tecnológicos que se están produciendo de forma acelerada desde comienzos del siglo XXI, obligan a repensar las finalidades y las formas de enseñanza-aprendizaje en ... -
Innovar la gobernanza de la investigación y la innovación: la experimentación de prácticas deliberativas en Europa
(Centro de Ciencias Sociales y Humanidades, Universidad Autónoma de Aguascalientes, 2020-09)En el marco de las políticas de investigación europeas hay una inclinación creciente por abrir a debate la propia definición de los problemas y los beneficios esperados asociados a su resolución. Ello ha adoptado la forma ... -
An Innovative Energy Harvesting Shock Absorber System for Motorbikes
(IEEE, 2022)This article presents an innovative energy recovery shock absorber system for motorcycles. The shock absorber is named synchronous pulley - energy harvesting shock absorber (SP-EHSA). The SP-EHSA is the first system ... -
Instrumentos de rendición de cuentas externos a los medios los casos de Andalucía y la CAPV
(Universidad Complutense de Madrid, 2019)Este artículo analiza los instrumentos de rendición de cuentas externos a los medios en Andalucía y la Comunidad Autónoma del País Vasco (CAPV), que serían los siguientes: asociaciones de espectadores; colegios, sindicatos ... -
Integral Design and Manufacturing Methodology of a Reduced-Scale Servo Press
(IEEE, 2021)In a context where industrial production boosts both the society and the economy of a country, improvements in industrial processes are key factors for efficient and reliable development of goods and products. New industrial ... -
Integral Sensor Fault Detection and Isolation for Railway Traction Drive
(MDPI AG, 2018)Due to the increasing importance of reliability and availability of electric traction drives in Railway applications, early detection of faults has become an important key for Railway traction drive manufacturers. Sensor ... -
An integrated inverse numerical–experimental approach to determine the dynamic Mode-I interlaminar fracture toughness of fibre composites
(Elsevier, 2022)A combined numerical–experimental methodology is presented to determine the dynamic Mode-I fracture properties of Fibre-Reinforced Polymer (FRP) composites. The experimental aspect consists of a modified Wedge-Double ... -
Integrated machine learning and probabilistic degradation approach for vessel electric motor prognostics
(Elsevier, 2023)In the transition towards more sustainable ships, electric motors (EM) are being used in ship propulsion systems to reduce emissions and increase efficiency. The safe operation of ships is crucial, and prognostics and ... -
Integration of Hot Isostatic Pressing and Heat Treatment for Advanced Modified gamma-TiAl TNM Alloys
(MDPI, 2022)The conventional processing route of TNM (Ti-Nb-Mo) alloys combines casting and Hot Isostatic Pressing (HIP) followed by forging and multiple heat treatments to establish optimum properties. This is a time-consuming and ... -
The Interaction between the Sheet/Tool Surface Texture and the Friction/Galling Behaviour on Aluminium Deep Drawing Operations
(MDPI, 2021)The increasing demands for lightweight design in the transport industry have led to an extensive use of lightweight materials such as aluminium alloys. The forming of aluminium sheets however presents significant challenges ...
