Simple record

dc.rights.licenseAttribution-NonCommercial-NoDerivatives 4.0 International*
dc.contributor.authorAlegre García, Raul
dc.contributor.authorArrazola Arriola, Pedro José
dc.contributor.otherTaylor, Chris M.
dc.contributor.otherDíaz, Fernanda
dc.contributor.otherKhan, Thawhid
dc.contributor.otherGriffin, James
dc.contributor.otherTurner, Sam
dc.date.accessioned2020-09-02T10:06:09Z
dc.date.available2020-09-02T10:06:09Z
dc.date.issued2020
dc.identifier.issn0264-1275en
dc.identifier.otherhttps://katalogoa.mondragon.edu/janium-bin/janium_login_opac.pl?find&ficha_no=159514en
dc.identifier.urihttp://hdl.handle.net/20.500.11984/1809
dc.description.abstractThis study generated novel behavioural data for three engineering steels undergoing a turning process. The materialswere hardened 410, PH13-8Mo and 300M, two stainless steels and one high strength steel respectively. A primary aimwas obtaining lowmachined surface roughness. A surface finish investigation compared tool geometries and tool materials.Multi-response cutting parameter screening was undertaken using a novel trade study and iteration method, where the calculated cut quality was used to identify better feed rates and surface speeds. In addition the sub-surface machined microstructure was examined. Tools with a small nose radius produced the roughest surfaces. A surface roughness below 0.4 μm Ra could be consistently achieved on all three materials using rhombic wiper inserts and a feed rate up to 0.1 mm/rev. PH13-8Mo had the lowest machined surface roughness, as low as 0.11 μm in terms of Ra. In the parameter screening stage a generalised recommendation for good cut quality was a surface speed of at least 120 m/min and a feed rate of 0.088mm/rev. The microstructure examination showed that for all materials under the conditions tested, therewas no evidence ofwhite amorphous layer formation and therewas grain deformation for the 410 material only.en
dc.description.sponsorshipTata Steeles
dc.description.sponsorshipUniversidad de Chilees
dc.language.isoengen
dc.publisherElsevier Ltd.en
dc.rights© 2020 The Authorsen
dc.rights.urihttp://creativecommons.org/licenses/by-nc-nd/4.0/*
dc.subjectHardened steelsen
dc.subjectTurningen
dc.subjectSurface finishen
dc.subjectMachinabilityen
dc.titleInvestigating the performance of 410, PH13-8Mo and 300M steelsin a turning process with a focus on surfacefinishen
dc.typeinfo:eu-repo/semantics/articleen
dcterms.accessRightsinfo:eu-repo/semantics/openAccessen
dcterms.sourceMaterials & Designen
dc.description.versioninfo:eu-repo/semantics/publishedVersionen
local.contributor.groupMecanizado de alto rendimientoes
local.description.peerreviewedtrueen
local.identifier.doihttps://doi.org/10.1016/j.matdes.2020.109062en
local.rights.publicationfeeAPCen
local.rights.publicationfeeamount1854 EUR (2200 USD)en
local.contributor.otherinstitutionUniversity of Sheffieldes
local.contributor.otherinstitutionUniversidad de Chilees
local.contributor.otherinstitutionManchester Metropolitan Universityes
local.contributor.otherinstitutionCoventry Universityes
local.source.detailsVol. 195. N. art. 109062, 2020en


Files in this item

Thumbnail
Thumbnail

This item appears in the following Collection(s)

Simple record

Attribution-NonCommercial-NoDerivatives 4.0 International
Except where otherwise noted, this item's license is described as Attribution-NonCommercial-NoDerivatives 4.0 International