Zerrendatu Artikuluak-Ingeniaritza honen arabera: izenburua
589-tik 47-66 emaitza erakusten
-
Ball-on-flat linear reciprocating tests: Critical assessment of wear volume determination methods and suggested improvements for ASTM D7755 standard
(Elsevier B.V., 2021)This work presents a critical assessment of wear volume determination methods for ball-on-flat linear reciprocating sliding tribological tests. It revealed that the ASTM D7755-11 standard leads to the highest relative ... -
BEAUD: A Browser Extension to Automatize End-User Deeds
(Elsevier, 2023)Web Augmentation allows anyone, computer-literate or not, to adapt the content, style or behavior of any web page. Searching for information is not always an undemanding task. The information searches carried out by users ... -
Behaviour of a Ternary Mixture with the Net Separation Ratio Close to Zero
(IOP Publishing, 2021)The behaviour of the ternary hydrocarbon mixture of toluene-methanol-cyclohexane in mass proportion 0.62/0.31/0.07 is studied. The direct numerical simulation is carried out for the two-dimensional closed cavity heated ... -
Best Practice Data Sharing Guidelines for Wind Turbine Fault Detection Model Evaluation
(MDPI, 2023)In this paper, a set of best practice data sharing guidelines for wind turbine fault detection model evaluation is developed, which can help practitioners overcome the main challenges of digitalisation. Digitalisation is ... -
Beyond customer satisfaction. Supporting organisational change through Service Design. A case study in the insurance industry
(Taylor & Francis, 2017)Insurance companies are in the midst of massive disruptive change occurring as a result of new consumption models and technologies. Companies unable to keep up with the rapid pace of change run the risk of disappearing. ... -
A Big Data implementation of the MANTIS Reference Architecture for Predictive Maintenance
(Sage Journals, 2019) -
Big Data Life Cycle in Shop-floor. Trends and Challenges
(IEEE, 2023)Big data is defined as a large set of data that could be structured or unstructured. In manufacturing shop-floor, big data incorporates data collected at every stage of the production process. This includes data from ... -
Binary Diffusion Coefficients for Short Chain Alcohols in Supercritical Carbon Dioxide-Experimental and Predictive Correlations
(MDPI, 2023)Experimental binary diffusion coefficients for short-chain alcohols in supercritical carbon dioxide were measured using the Taylor dispersion technique in a temperature range of 306.15 K to 331.15 K and along the 10.5 MPa ... -
Broaching: Cutting tools and machine tools for manufacturing high quality features in components
(Elsevier Ltd., 2020)Broaching is a unique machining process with high accuracy and surface quality, which is employed in massand batch production for the manufacture of components with highly complex geometries. It involves the use of ... -
Budget impact analysis of the use of Souvenaid in patients with prodromal Alzheimer’s Disease in Spain
(Springer Nature, 2022)Introduction The effectiveness, safety, and cost-effectiveness of the use of Souvenaid for Alzheimer’s disease (AD) have been previously evidenced. To complete the economic analysis, there is a need to assess whether ... -
Business Model Innovation in Established SMEs: A Configurational Approach
(MDPI, 2020)Small and medium-sized enterprises (SMEs) are at the heart of a nation’s wealth creation, employment generation and economic development. To help SMEs stay competitive in a fast-changing environment, researchers have ... -
Business model innovation through industry 4.0: a review
(Elsevier B.V., 2018)The following article presents a brief literature review conducted to extend our knowledge about how Industry 4.0 affects business models and to identify business model innovations derived in consequence. Based on the ... -
Calendar Ageing Model for Li-Ion Batteries Using Transfer Learning Methods
(MDPI, 2021)Getting accurate lifetime predictions for a particular cell chemistry remains a challenging process, largely dependent on time and cost-intensive experimental battery testing. This paper proposes a transfer learning (TL) ... -
Canonical correlation analysis of the impact of the ICT on the diversification performance
(Inderscience Publishing, 2020)The main objective of this study was to establish the relationship between the use of information and communication technologies (ICT) and the performance of business diversification within a sample of companies belonging ... -
Capacity buffer management in implementing drum-buffer-rope methodology in make-to-order environments
(Federación de Asociaciones de Ingenieros Industriales de España, 2022)The research work conducted by Orue et al. [1] aims to analyze the impact of protective capacity on the application of the third step of the drum-buffer-rope methodology of the theory of constraints (subordinate everything ... -
The capacity of statistical features extracted from multiple signals to predict tool wear in the drilling process
(Springer Verlag, 2019)Industrial processes are being developed under a new scenario based on the digitalisation of manufacturing processes.Through this, it is intended to improve the management of resources, decision-making, ... -
Capturing near-field circular dichroism enhancements from far-field measurements
(American Physical Society, 2024)Molecular circular dichroism (CD) spectroscopy faces significant limitations due to the inherent weakness of chiroptical light-matter interactions. In this view, resonant optical antennas constitute a promising solution ... -
A Case Study of Entrepreneurial Intent Among Students of the Primary Education Degree in the Basque Country and the Performance of Education Faculties
(Richtmann, 2022)Entrepreneurship is a key competence for anyone intending to be an active citizen and obtain employment. Entrepreneurial education is therefore essential at all levels of education and in every field, not only in business ... -
Case Study of the Experience Capturer Evaluation Tool in the Design Process of an Industrial HMI
(MDPI AG, 2020)In the absence of user experience evaluation tools for industrial human–machine interfaces (HMI), a specific tool called eXperience Capturer (XC) has been created. It is a multi-method user-centred tool that evaluates the ... -
A case study on the use of machine learning techniques for supporting technology watch
(Elsevier, 2018)Technology Watch human agents have to read many documents in order to manually categorize and dispatch them to the correct expert, that will later add valued information to each document. In this two step process, the first ...
